• Summary
  • Features
  • Specs
  • Accessories
  • Parts
  • Brochure
  • Quote

These vertical knee mills are equipped with vari-speed drive. The dove tail ways chromed and the box ways are hardened and ground.

Features, Function, & Benefits:

ISO 9002 Certified:
Quality Up To World Industry Standards.

Meehanite Casting:
Highest Grade Of Casting Possible.

A Pair Of Precision ABEC-7 Angular Contact Bearings To Support Spindle.  The Quill Is Ground And Chromed To Fit The Housing:
This Insures A Spindle Run out Of .0004” T.I.R.

Motor Shaft And Varidrive Pulleys Are Dynamically Balanced, Then Chromed For A Flawless Fit, Ground Ribs On Inside Diameter:
For Smooth Speed Changes.

Motor Shaft Has An Oil Channel In The Center That Is Fed By A Grease Fitting On The Lower End:
To Keep Vari-Drive Pulley Moving Smoothly On The Shaft.

This LMV-49DVS Mill Uses A Roller Bearing For The Lower Support Of The Shaft: It Ensures Proper Loading, Support And Alignment It Also Prevents The Shaft From Being Distorted By The Tension Of The Belt:
For Quiet, Accurate Operation At Any Speed For Years And Years.

One Shot Lubrication System:
For Lubrication Of Ways And Lead Screws. (X,Y And Z-Axis)

Hand Scraped Saddle And Knee:
For Better Oil Retention.  It Avoids Having Chips And Dirt Embed In The Knee And Damage The Sliding Surface.

Oil Groove Are Milled:
For Maximum Lubrication On All Wear Areas.

Table And Saddle Backlash Is Controlled By Double Nut Design:
Keeps Lead Screw In Contact With Bronze Nuts An All Times To Keep Backlash At .0008” Within 20”.

Table And Saddle Are Mounted With Thrust Bearings That Are Pre Loaded:
Eliminating Endplay For Precisely Controlled Lateral Movement.

Patient Knuckle Design Uses 6 Bolt 3 Per Side, Securing Them From The Outside:
This Method Locks The Head Securely Resulting In Better Accuracy And Performance.


Working surface 9” x 49"
T-slot number, size 3, 5/8"
Table travel (X,Y,Z) 36.6" x 12" x 5"
Ram travel 12"
Knee travel 16"
Spindle to column (min-max) 6 3/4" - 18-1/2"
Spindle to nose table 2 1/8” - 18"
Motor 3 HP
Spindle Nose Taper R-8
Digital Variable Speed 60 ~ 4,500 RPM
Quill feed (IPR) 0.0015”, 0.003”, 0.006"
Head swivel 360º
Head tilt; right-to-left (each way) 45º
Head tilt up-and-down (each way) 45º
Floor area (w x d x h) 52" x 55" x 82.7"
Net weight 2280 Lbs.


  • DVS Head
  • Hard-chromed ways
  • Precision Ground and Flaked Table
  • Unique Double Nut Backlash System
  • Double Fan Cooling System
  • Cutler Hammer On/Off Switch 
  • One-shot lube system 
  • Front and rear rubber way covers 
  • Tool kit 


  • 440 V Transformer - 3HP
  • Auto Lube Pump w/ 2 adjustments
  • 6" Kurt Vise with Swivel Base D688
  • Righ Angle Milling Attachment with Arbor
  • Drill Chuck & Drill Arbor
  • Coolant system with chip pan
  • Maxi Torque Rite Power Draw Bar
  • Riser block (4”, 7”) 
  • R-8 Collet Set of 11 (1/8"-3/4" by 1/16")
  • Clamping Kit 
  • Halogen work light 
  • Spare Kit

Please contact our parts department at 310-370-5990.

Get a Quote

*Prices may vary based on location